User Settings Test (15 min)

NOTES:
	- the settings button is located in the bottom-left corner of the Ladder
	- the "Default" tab will be referred to as [DTab], "Custom" as [CTab]
	- the "Use Defaults" checkbox is located at the top of the dialog
	- when "Use Defaults" is checked, [CTab] is disabled ([DTab], however, is always enabled)
	- to Import/Export settings to files, click the hamburger icon in the upper-right corner of the settings dialog.

	- you cannot open multiple settings dialog for the same Ladder
		i) if a settings dialog is already open, clicking the settings button in the Ladder again closes said dialog, then opens a new one
	- the settings dialogs do not live update
		i) this only pertains to [DTab], as Custom settings are not shared.
	- commit changes by clicking "Apply" or "OK"
		i) the only difference between the 2 buttons is that "OK" also closes the dialog
	- when you commit changes:
		i) even if "Use Defaults" is NOT checked, the settings in [DTab] will be compared with the current defaults,
		   if they are different, the default changes will be committed as well.
		ii) be advised of the following scenario:
			You have 2 settings dialogs open (call them [A] and [B]), and commit changes to the defaults in [A].
			As the dialogs do NOT live update, [B] will have stale defaults.
			When you click commit in [B] (even if you have not actually changed anything in [DTab])
			the stale defaults in [B] will be committed, effectively overwritting the changes to the defaults you just committed from [A].
	LASTLY:
		- when the test directs you to "Visually Confirm blah...," just give it a quick glance, if something isn't matching it should be obvious.
		- when the test directs you to repeat a step for each property:
			i) ignore the "Order Badge Style" (for now...), it is not actually hooked up to the ladder
			ii) the rest is self-explanatory: there are 2 grids, click each cell to open a popup and change the value
			iii) in the FontPicker popup, change font family, weight, and size
			iv) the Sample column is purely output, don't bother clicking it
		- when the test advises you to name files (screenshots, or ladder settings files), it is because they will be referenced later by that name.
		- if you uncheck all 3 market break lines, the ladder resolves to show the bid line by design.

------------TEST STEPS------------------

1) Launch 2 Ladders of the same Security
	- the security needs a few working orders on both sides, and a gap of 5-8 ticks between the top bid/ask.
	  The gap causes is needed to separate the market break lines (Bid, Ask, and Mid).
	- from hence forth, the 2 ladders will be referred to as "[A]" and "[B]" and their settings dialogs as "dialog[A]" and "dialog[B]"
	- at the risk of sounding redundant, the "Default" tab will be referred to as [DTab], the "Custom" as [CTab]
	
2) Open the settings dialogs for [A] and [B]

3) Make sure that both [A] and [B] are using default settings, then close [B]dialog

4) In dialog[A] (with [DTab] selected, [CTab] should be disabled anyways), change each property, then click "Apply"

5) Visually confirm that all the changes have been applied to both ladders
	- the row height should adjust to fit the largest font size,
	- the scroll position should be maintained, assuming the AutoRecenterTimer didn't move it.
	
6) Take a screenshot, name it "A-1-confirmation.png"

7) In dialog[A], export the default settings to a file, name it "A-1.ladder" (instructions on how to import/export are in the NOTES section)

8) In dialog[A], click "Restore to Factory," then click "Apply"

9) Visually confirm that dialog[A], and both ladders, each changed appearance, and match one another.

10) In dialog[A], uncheck "Use Defaults", then select [CTab]

11) Import "A-1.ladder" to Custom, then click Apply

12) Visually confirm that:
	- dialog[A] and [A] changed appearance, and look just like they did in "A-1-confirmation.png"
	- [B] did not change appearance

13) Click the settings button in [A] and [B] to get 2 fresh dialogs (dialog[A] should close and reopen)
	- in dialog[A], "Use Default" should be false, and [CTab] selected
	- in dialog[B], "Use Default" should be true, and [DTab] selected ([CTab] should be disabled)

14) Take a screenshot, then save the workspace, then restore it
	- visually confirm that [A] and [B] look as they did in the screenshot
	- repeat step 13

15) In dialog[A], with [CTab] selected, click "Copy from Default"
	- [CTab] should now have the same settings as [DTab]

16) Click the settings button in [A] to close and reopen dialog[A]

17) In dialog[A] select [DTab], then click "Copy from Custom"
	- [DTab] should now have the same settings as [CTab]

DONE!!!